E-mon Energy Software User Manual Page 141
- Page / 223
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Access Location
E-Mon Energy User Manual 14-4 E-MON
Flag Status Button
The Flag Status provides an alert in the E-Mon Energy™ software of a problem or power failure. The two
failures illustrated below indicate the date and time of the last failure. The Power Failure Status indicates that
the IDR has lost power at some point. To reset (clear) the flags, click on the Clear Flag button. For complete
instructions, see Error Flag section within this manual.
Figure 14.8 - Access Location Function – Flag Status
Columns Description
Status
This column displays the condition of the device. If the condition
states “Bad” or “Timeout,” there is a possible error in reading the
device and there may be a hardware or communication issue. If the
condition is “ok,” the hardware is functioning normally.
Power Failure Status
This column displays the total number of Power Failures and the
date/time of the last occurrence, since it was last reset. In this
example, there were more than 15 power failures and the last time
occurred on 12/30 at 15:44.
Tamper Alarm
This column displays an active <on> flag when a door is open on
the recorder. If the Tamper Alarm is not on, the column will display
<off>.
O’Load (Over Load)
This column displays an overload flag when the meter has
excessive amperage (i.e. 200 amp load through the sensors on a 100
amp meter). When no problem exist the column display <none>.
Power
This column displays any general power/voltage errors with the
meter (i.e. low, noisy or unstable). Low = voltage drop below
nominal level, noisy = dirty power supply, harmonics) unstable =
fluctuating levels. When no problems exist, the column displays
<normal>.
MTR Reg
This column displays any malfunctions with the recorder real-time
clock (i.e. <Bad>). When no problems exist, the column displays
<ok>.
IDR State
This column will display any problems that may exist with the
functionality of the IDR. When no problems exist, the column
displays <ok>
- User’s Manual 1
- Table of Contents 4
- Section 7 Group and Location 5
- Section 8 Recorder 6
- Section 9 Meter 6
- Section 10 Virtual Meter 6
- Section 11 Customer 7
- Section 13 Other Features 7
- Section 14 Access Location 7
- Section 15 Errors and Flags 8
- Section 17 Real-Time Graphs 8
- Introduction 10
- What is E-Mon Energy™? 10
- Benefits of E-Mon Energy 10
- About This Manual 10
- Using This Manual 11
- Notation Conventions 12
- Usage Conventions 12
- Icons in the Margins 13
- Related Documentation 13
- If You Need Help 13
- System Configuration Overview 14
- AMR On-Site Configuration 16
- AMR Off-Site Configuration 17
- Installing E-Mon Energy 18
- Logging into the System 23
- Logging out of the System 24
- How do I use E-Mon Energy™? 28
- What is the Menu Bar? 29
- Device Explorer Button 30
- Parent Window 31
- Child Windows 31
- Pop-Up Dialog Boxes 32
- Pop-Up Menus 32
- Pop-Up Calendars 33
- Messages Dialogs 33
- Navigation Buttons 36
- Action Buttons 36
- Connection Parameters 38
- Ethernet 39
- What is the AMR Panel? 49
- What are AMR Icons? 49
- What is the Schedule Panel? 50
- What is the TASK Panel? 51
- What is the Server Panel? 53
- How do I Set Up the Tasks? 55
- How do I Set Up the Server? 56
- Group and Location 58
- What are Group and Location? 58
- What is the Group Panel? 59
- How do I Add New Group? 62
- Updating the Device Explorer 63
- USTOMIZE button. A 64
- What is the Location Panel? 65
- Setting up a New Location 70
- Option) 72
- Select Location 73
- What is a Recorder? 78
- What is the Recorder Panel? 78
- Communication Setup 80
- What is the Access Window? 84
- Recorder Procedures 87
- Scanning Recorder 88
- Updating the Database 88
- Initializing the Recorder 92
- Verifying the Recorders 95
- What is a Meter? 96
- What is a Submeter? 96
- Select Meter Location 100
- rather than NEW 101
- Reading the Meter Hardware 102
- What is a Virtual Meter? 104
- Virtual Meter 104
- Setting up a Location Tab 106
- Update the Device Explorer 107
- Creating a Virtual Recorder 108
- Creating a Virtual Meter 109
- +” button to add a new 109
- Customer 114
- What is the Customer Panel? 115
- How do I add a Customer? 116
- Adding a Billing Device 118
- Rate Table and TOU Schedule 120
- How is the Rate Table used? 125
- charges 131
- Other Features 132
- What are the Other Features? 132
- Recorder 134
- Security 135
- Access Location 138
- What Is the Access Location? 138
- What Are the Functions? 138
- Read Hardware Functions 140
- Flag Status Button 141
- Profile Status Button 142
- Version/Time Button 143
- Verify Hardware Functions 144
- Verify Meters Button 145
- Verify AMR Button 146
- Setup Hardware Functions 147
- Initialize Recorder Button 148
- Update Database Button 148
- Access Database Functions 149
- Load Graph Functions 150
- Power Graph Functions 150
- Error and Flags 152
- What Are the Error Flags? 152
- What Is a Connection Error? 152
- What Is a Protocol Error? 152
- What Is a Profile Error? 152
- What Is a Billing Error? 153
- What Is a Flag Status? 154
- Checking the Flag Status 155
- Clearing a Flag Status 155
- Demand Profile Graph 156
- How Is the Data Stored? 157
- Can I Print the Graph? 159
- To Load a Profile 160
- Plotting the Graph 162
- Navigating in the Graph 163
- Other viewing options are: 164
- Printing a Graph 164
- Exporting Graph Data 165
- Creating a Pie Chart 166
- Selecting Graph Options 167
- Real-Time Graphs 168
- What Is the Statistic Table? 169
- What Is the Power Graph? 170
- To Load the Power Graph 173
- Billing and Reports 176
- Bill Cycle Definition 185
- Auto Bill Cycle Setup 186
- Meters using the Bill Cycle 186
- Auto Bill Cycle Scheduler 186
- Consumption Report(s) 189
- Saving or Printing the Bill 191
- Billing Period Options 192
- Troubleshooting 194
- Software? 194
- Using Help 195
- Glossary 198
- E-MON 207
- Flag Codes 208
- Modem Functions 209
- TCP Functions 210
- Reference Guide 214
- Connect and Read Meters 214
- Generate Bills 214
- Graph Load Profile 215
- Billing Templates 216
- E-Mon Energy User Manual D-2 217
- CROSS SEASON STANDARD FORMS: 218
© 2020, manymanuals.com. All rights reserved. | 0.815 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals